Water Quality Analysis Instrument

FAQs on the principles, selection and maintenance of pH/ORP, conductivity, dissolved oxygen and other water quality analysis instruments

50 questions in total. Click a title to expand the answer.

How should calibration buffer solutions be stored and used?

Standard buffer solutions should be sealed, protected from light, and stored at the temperature specified in the instructions; do not use them once expired or contaminated. During calibration, rinse the electrode with a small amount of buffer solution to avoid cross-contamination; after use, immediately […]

How should a water quality analyser be handled when taken out of service for an extended period?

Remove the electrode and store it as instructed (immerse pH electrodes in KCl solution; store DO electrodes dry or as instructed), drain the flow-through cell, clean the measuring assembly, and switch off the power […]

Where can I find the specifications for a particular water quality analyser model?

Refer to the manufacturer's official data sheet and verify the measuring range, accuracy, temperature compensation, ingress/explosion protection rating, output signal, and electrode compatibility. The product pages on this site compile D […]

What should be done about electrode scaling in highly contaminated media?

Use a measuring assembly with a cleaning function (e.g. the □HC-7 series with cleaning function, or the LHC-7D top-lift jet cleaning), or switch to an electromagnetic induction conductivity […]

Do water quality analysers require periodic verification?

Instruments such as pH/conductivity meters used for metering or environmental emission monitoring generally require periodic verification in accordance with metrology regulations; for general process control instruments, follow the manufacturer's recommendations and internal quality management […]

What should be noted when maintaining explosion-proof water quality instruments?

Do not open the cover or disassemble the instrument while it is energised in a hazardous area; maintenance requires a work permit, and the explosion-proof construction must be kept intact (sealing rings, flameproof joints, cable glands); replacement parts must be of the same model […]

How should a dissolved oxygen electrode be maintained?

The membrane and electrolyte of a DO electrode must be replaced periodically, the probe surface kept clean, and calibration (zero and span) performed at regular intervals. Low-concentration measurement is more sensitive to the condition of the membrane and electrolyte […]

What is the electrode constant of a conductivity meter?

The electrode constant is a parameter of the electrode's geometry (cm⁻¹) used to convert the measured conductance into conductivity. Electrodes with different constants are used for different ranges: low conductivity uses […]

What should be noted when measuring ORP?

The ORP electrode surface is prone to contamination or scaling and requires regular cleaning; ORP readings reflect the redox state rather than a specific ion concentration, so interpretation should take the process into account […]

What happens if temperature compensation fails?

Failed temperature compensation or a faulty sensor will cause the pH reading to drift with temperature and produce a systematic deviation. Check the connection and reading of the temperature sensor such as Pt1000 […]

How is a field pH transmitter wired?

Connect the electrode signal (including the temperature compensation terminals), power supply and output signal according to the terminal markings, and ensure the electrode connector is dry and clean with shielded grounding. Two-wire (e.g. SHBM […]

How often should the electrode be replaced?

It depends on the medium, temperature and intensity of use; typically the service life of an industrial online pH electrode ranges from several months to two years. When the calibration slope deviates significantly, the response slows, the reading continues […]

What routine maintenance does an online pH meter require?

Check electrode contamination and scaling, calibration validity, remaining standard solution, wiring and terminals, transmitter indicator lights and output signal; for units with a cleaning function (e.g. □HC- […]

How is a pH electrode calibrated? How often?

Perform two-point calibration with at least two standard buffer solutions (e.g. pH 4.01 and 6.86 or 9.18): clean the electrode → immerse in the first buffer […]

How do I troubleshoot pH reading drift or instability?

Troubleshoot in the order "electrode—calibration—wiring—medium": whether the electrode is contaminated or aged, whether the calibration is valid, whether the wiring is damp or loose, […]

Does a pH electrode need to be stored immersed?

Yes. The glass bulb of a pH electrode must be kept moist; when not in use for a short period it should be immersed in 3 mol/L KCl solution or a dedicated storage solution, and must not be stored dry or immersed […]

What are common pitfalls in selecting water quality analysers?

Four types of pitfalls: first, using an ordinary pH electrode to measure pure water, causing reading drift; second, failing to select intrinsically safe instruments for explosion-proof areas; third, selecting a contacting conductivity […]

Where can I find detailed specifications for water quality analysers?

Refer to the manufacturer's official data sheet to verify the measuring range, accuracy, temperature compensation, ingress protection rating, explosion protection marking and output signal. The product pages on this site summarise DKK, […]

How is the measuring range determined? Can it be exceeded?

The range should cover the normal range of the actual process parameters with a margin. pH is typically 0–14 universal; ORP depends on the model and can reach -2000 to + […]

Electromagnetic induction vs contacting conductivity meter: how to choose?

For clean, low-conductivity media choose the contacting (electrode) type for high sensitivity; for highly contaminated, high-concentration, particulate-laden or scaling media choose the electromagnetic induction type for non-contact, low-maintenance […]

How to choose for low-concentration dissolved oxygen measurement?

Low-concentration DO applications such as boiler feedwater require dedicated low-concentration instruments. On this site, OBM-300 (for low concentration), ODM-110A (industrial low concentration […]

How do water quality analyser output signals connect to DCS/PLC?

Most water quality transmitters output 4–20 mA (e.g. GPHU), which can connect directly to DCS/PLC analogue inputs. For long distances or high-interference environments, […]

What does cartridge-type electrode mean? What are the benefits?

The cartridge design makes the sensing element a quickly replaceable cartridge, so replacement does not require changing the entire electrode or re-soldering, reducing maintenance […]

How to choose the calibration method? Is automatic calibration important?

Automatic calibration simplifies operation and reduces human error. The HDM-135A industrial pH converter on this site simplifies complex standard solution calibration procedures, […]

Conductivity, resistivity, TDS, salinity: how to choose?

Choose according to water quality and monitoring purpose: conductivity for general water quality, resistivity for ultrapure water, salinity for saline media, and TDS for total dissolved solids. On this site, BSX21 […]

Immersion type vs flow-through type measuring assembly: how to choose?

The immersion type is immersed directly in a tank/basin and suits online monitoring of large water bodies; the flow-through type is installed in a pipe bypass and suits pipeline media with controllable flow. On this site, HC- […]

How to choose a pH electrode for bioengineering/fermentation?

Biological fermentation requires a dedicated, durable electrode capable of steam sterilisation (SIP). The ELP-045 pH electrode for bioengineering on this site is designed for this application; dissolved […]

How to choose between a two-wire and a four-wire transmitter?

Two-wire transmitters are powered by the signal loop, offer simple wiring and suit long distances and intrinsically safe circuits; four-wire transmitters have an independent power supply, more complete functions and stronger drive capability. On-site SHBM-1 […]

How to choose pH measurement for pure water/boiler water?

A dedicated low-conductivity measurement solution is required. The on-site HC-G65 pure water measurement device can measure the pH of low-conductivity water above 0.01 mS/m, equipped with […]

How to choose pH electrodes and instruments for wastewater/highly contaminated media?

Choose contamination-resistant, easy-to-clean electrodes and flow-through assemblies. The on-site 8833 submersible pH/ORP detector with cleaning function □HC-7 series […]

How to decide whether to measure pH or ORP?

Choose pH if acidity/alkalinity is of concern (e.g. neutralisation control, pH compliance of discharge); choose […] if redox status is of concern (e.g. chlorination disinfection, dechlorination, cyanide-containing wastewater treatment).

How to choose between field-mounted and panel-mounted instruments?

Field-mounted instruments (e.g. HDM-135A, GPHU) are installed close to the measurement point for local display and transmission, reducing long-distance analogue signal transmission; panel-mounted instruments (e.g. H […]

How to choose pH/ORP instruments for explosion-proof applications?

For hazardous area applications, select intrinsically safe products with explosion protection certification. The SHBM-161 intrinsically safe explosion-proof pH/ORP converter (2 […] on this site.

How to interpret the ingress protection rating of water quality analysis instruments?

The ingress protection (IP) rating indicates the enclosure's dust and water resistance; field-mounted instruments should achieve a certain IP rating. The on-site SHBM-161 intrinsically safe explosion-proof […]

What is the first step in selecting a pH/ORP analyser?

The first step is to define the measurement parameters and medium: pH, ORP or both; whether the medium is clean water, wastewater, pure water or highly contaminated/particle-containing liquid; temperature, pressure […]

What is resistivity measurement? Why is resistivity used for ultrapure water?

Resistivity is the reciprocal of conductivity. Ultrapure water contains very few ions and has extremely low conductivity, so expressing it as resistivity (MΩ·cm) is more intuitive and more accurate. The on-site AQM- […]

What does a dissolved oxygen (DO) analyser measure? Where is it used?

A dissolved oxygen analyser measures the concentration of oxygen dissolved in water and is widely used in wastewater treatment aeration control, aquaculture, boiler feedwater deaeration monitoring, biological fermentation, etc. The on-site O […]

What is an electromagnetic induction conductivity meter? What are its advantages?

Electromagnetic induction (electrodeless) conductivity meters measure via electromagnetic induction; the electrodes do not come into direct contact with the medium, making them resistant to scaling and corrosion, and suitable for highly contaminated, high-concentration or particle-containing […]

What is the difference between a pH transmitter and a pH converter?

The two have similar functions, both converting electrode signals into standard outputs. By convention, "transmitter" emphasises local field mounting and output […].

How is the pH measurement signal transmitted to the control system?

The converter/transmitter converts the electrode's millivolt signal into a standard analogue signal (4–20 mA or 0–10 V) for transmission to the DCS/PLC; some […]

What does a conductivity analyser measure? What is its relationship to pH?

Conductivity reflects the ability of an aqueous solution to conduct electricity, indirectly reflecting the total dissolved ions, and is commonly used for pure water quality, concentration and salinity monitoring. It is a different water […] from pH (acidity/alkalinity).

What is the difference between online pH analysis and a laboratory pH meter?

Laboratory pH meters are used for intermittent sampling measurements, emphasising portability and versatility; online pH analysers are permanently installed in the field or on pipelines, emphasising continuous operation, […]

What are the difficulties of pH measurement in pure water/low-conductivity water?

Pure water has a low ion concentration and weak buffering capacity; the electrode is susceptible to streaming potential, liquid junction potential and contamination, resulting in unstable measurement and slow response, requiring dedicated low-conductivity measurement solutions […]

Can pH and ORP be measured on a single instrument?

Yes. A dual-channel analyser can connect both pH and ORP electrodes, displaying and outputting them separately. The BSP2200D on this site is a pH/PID […]

What is a combination pH electrode?

A combination electrode integrates the pH indicating electrode and the reference electrode into a single probe; it is compact and easy to use, and is the mainstream form of industrial online pH measurement. The […] on this site

What does the pH range of 0–14 mean?

pH is a negative logarithmic scale of hydrogen ion activity; at room temperature, neutral is 7, acidic solutions are below 7 and alkaline above 7. 0–14 is the practical […] for common aqueous solutions

What is ORP? What does an ORP meter measure?

ORP (Oxidation-Reduction Potential) reflects the redox state of a solution, with the unit […]

Why do pH electrodes require temperature compensation?

The electrode potential slope varies with temperature (the temperature term in the Nernst equation), so the same solution measured at different temperatures yields different potentials. Temperature compensation works by measuring the solution temperature […]

What are the components of a pH measurement system?

A typical system includes: a pH combination electrode (indicator electrode + reference electrode), a temperature compensation element, a converter/transmitter, a flow-through cell or immersion assembly, and calibration […]

What is a pH meter and what does it measure?

A pH meter is an instrument used to measure the acidity or alkalinity (pH value) of aqueous solutions. The pH value represents the negative logarithm of the hydrogen ion activity in solution, typically ranging from 0 to 14: 7 […]

Online customer service
Online customer service Scan or click to contact directly
Contacts
Miss Chen(Safety barriers, isolators, surge protectors)
Ms Chen Personal WeChat QR Code

Scan WeChat QR code to add personal WeChat

QQ:2501529964

Phone:17717626508

Email:chenjing@qishan-sh.com

Miss Lu(Field Instruments, Valve Accessories, Terminal Blocks)
Ms Lu Personal WeChat QR Code

Scan WeChat QR code to add personal WeChat

QQ:1695457483

Phone:13636420802

Email:lhm@qishan-sh.com

Mr. Ye(Technical Support, After-Sales Service)

QQ:97010638

Phone:15800474322

Email:web@qishan-sh.com

Online Message

Please fill in the name

Please fill in a valid contact phone number (7-20 digits)

Please enter a valid email address

Please enter the requirement description (at least 10 characters)