Surge Protectors
FAQs on surge protector principles, selection, use and maintenance
50 questions in total. Click a title to expand the answer.
What consequences can SPD failure cause?
SPD failure (open circuit) means loss of surge protection. When the next surge arrives, the protected equipment directly withstands the overvoltage, which may damage instruments, I/O modules or even […]
Where can I find detailed parameters for a specific SPD model?
Refer to the manufacturer's official datasheet and verify rated voltage, current-carrying capacity, clamping voltage, response time, number of channels, wiring method and certification. The product pages on this site compile […]
How should commissioning checks be carried out after installing a new SPD?
Check four items: first, wiring polarity and shield grounding are correct; second, grounding is continuous and resistance meets requirements; third, status indication is normal (no degradation alarm); fourth, the protected […]
Does shield grounding greatly affect SPD performance?
Yes, significantly. Correct grounding of the signal cable shield can greatly reduce induced surges. The M-LBAS-IA1.DE on this site specifies that the cable shield is directly grounded, […]
What is the service life of an SPD?
An SPD has no clearly fixed service life; it depends on the number and intensity of surge impulses. After degradation, protection capability decreases, and replacement timing should be judged by status indication and inspection. In areas with frequent thunderstorms […]
What is the difference between an SPD and a UPS/voltage stabiliser?
A UPS provides continued supply during power failure, and a voltage stabiliser handles continuous voltage fluctuations; an SPD handles microsecond-level transient surges. The three operate on different time scales and cannot replace one another […]
What must be done after replacing the SPD in an intrinsically safe circuit?
Confirm the model and certification parameters match (compliant with FISCO/2-WISE, etc.), check shield grounding, verify that intrinsically safe circuit parameters are unchanged, and if necessary perform […]
What is the relationship between SPDs and equipotential bonding?
An SPD is only effective when combined with proper equipotential bonding. If a ground potential difference exists between devices, surges will strike back through the earthing system. Equipotential bonding connects the […] of each device
What should I do if the signal is attenuated after installing an SPD?
Check whether a standard power SPD has been mistakenly used on a signal circuit (excessive parasitic capacitance), or whether the SPD bandwidth is insufficient. A low-capacitance signal/bus-specific […] should be used instead.
Can an SPD be replaced while energised?
Replacement should generally be carried out with the power off, especially for intrinsically safe circuits and interlock circuits. Hot plugging may cause sparks or transient overvoltages and compromise the intrinsic safety status. Before replacement, perform the […]
Do SPDs need to be inspected after a lightning strike?
Yes. After a lightning strike or an obvious surge event, check the SPD status indicator, the earthing connection and the operation of the protected equipment. If the SPD indicates degradation or failure, […]
What are the routine inspection items for an SPD?
Check whether the status indicator is normal, whether the wiring is loose, for signs of overheating/corrosion/water ingress, whether the earthing is intact, and whether the backup protection (fuse/circuit breaker) is […]
How do I troubleshoot an SPD nuisance trip (alarm during normal operation)?
First confirm whether the actual line voltage exceeds the SPD rated voltage (an undersized selection will cause nuisance tripping); then check whether the wiring forms an abnormal loop with the shield/earth; then […]
How is an SPD wired?
Connect the input (line side), output (equipment side) and earth terminal according to the terminal markings, and observe signal polarity. The shield is earthed directly as required by the product (e.g. M-LBAS- […]
What are the considerations for SPD installation location?
It should be installed as close as possible to the protected equipment or the line entry point to shorten the protection distance and reduce surge induction on the cable. Signal SPDs are often installed at the cabinet entry or on-site junction […]
How should an SPD be earthed to be effective?
The earthing conductor should be short, straight and of low impedance, avoiding coils; connect it to a reliable equipotential earthing network. The shield earthing of a signal SPD should be single-point or multi-point as required by the system, […]
Can signal SPDs and power SPDs be used interchangeably?
No. Power SPDs differ greatly from signal SPDs in voltage rating and surge current capacity, and their parasitic capacitance would compromise signal integrity. Signal circuits must use signal […]
Where can I find detailed SPD parameters?
Refer to the manufacturer's official data sheet and verify rated voltage, discharge capacity, clamping voltage, response time, number of channels and intrinsically safe certification. The product pages on this site summarise P+F […]
Does an SPD need to match the operating environment?
Yes. Ambient temperature, humidity, altitude, degree of protection and installation method all affect SPD selection. For outdoor installation or installation in on-site junction boxes, select the corresponding degree of protection […]
What should be noted when replacing an SPD?
Confirm that the model, number of channels, voltage level and discharge capacity match the original circuit; in particular, intrinsically safe circuits must retain unchanged intrinsically safe certification parameters. After replacement, check the earth connection and status […]
What are common pitfalls in SPD selection?
Four pitfalls: first, using a power SPD to protect a signal circuit, where voltage and capacitance do not match; second, using a standard SPD in an intrinsically safe circuit, which compromises the intrinsically safe parameters; […]
How can you tell whether an SPD needs replacing?
Check the status indicator (e.g. window colour change, LED alarm, remote signalling output) and combine this with lightning strike records and service life. Models with a fault status module allow remote monitoring […]
How should the backup protection for an SPD be configured?
Configure a fuse or circuit breaker of the specified rating in accordance with the product manual, to provide safe disconnection when the SPD fails. Do not arbitrarily increase the backup protection rating, otherwise the SPD […]
Does the earthing method affect SPD selection?
Yes. In locations with poor earthing grid quality or earth potential differences, select a solution capable of handling earth potential differences (e.g. SPDs dedicated to unearthed signal lines). The M-LB […] on this site
How should surge protection, isolators and safety barriers be selected together?
The three have different roles: an SPD discharges transient surges, an isolator conditions signals, and a safety barrier limits intrinsically safe energy. In critical circuits, an SPD can be installed on the field side to discharge locally […]
How to choose between DIN-rail and field-housing SPDs?
DIN-rail versions are installed in cabinets, facilitating centralised installation and maintenance, and are suitable for centralised protection before signals enter the control system; field-housing versions are installed close to field devices and can […] surges
Should the SPD status monitoring/remote signalling function be selected?
For critical circuits, select models with status indication or remote signalling output to enable remote monitoring of SPD degradation and timely replacement. The M-LB-4400 […] on this site.
How to select SPDs for intrinsically safe circuits?
You must select a model that meets intrinsic safety requirements and does not compromise the circuit's intrinsic safety parameters, such as dedicated products compliant with FISCO and 2-WISE. On-site M-LBA […]
Key points for selecting fieldbus SPDs?
Confirm the bus type (Profibus/PA, Foundation Fieldbus, CAN, Ethernet-APL […]
Who is the solution of plugging an SPD onto a KF module suitable for?
Suitable for applications already using P+F K-series KF modules where surge protection is to be added on the field side. On-site P-LB-1.C.123 directly […]
How to select the number of channels for an SPD?
Select according to the number of signal lines requiring protection. On-site M-LB-Ex-2615 is 3-channel, M-LB-Ex-2112/2114/2 […]
How to select the discharge capacity (kA)?
Select according to line exposure and local thunderstorm days. Overhead lines, long-distance cables and thunderstorm-prone areas require higher discharge capacity; indoor short-distance shielded cables may be reduced appropriately. On-site […]
Is the response speed of a surge protective device important?
Yes. Lightning surges rise extremely fast (microsecond level); the slower the SPD response, the higher the transient overvoltage the equipment withstands. The response time of signal SPDs is typically in the nano […]
What is the first step in SPD selection?
The first step is to clarify the type of line to be protected: power, analogue signal, digital signal, fieldbus or Ethernet. SPDs for different lines differ in voltage level, capacitance, […]
How to select the voltage level of a signal circuit SPD?
The rated voltage of the SPD should be slightly higher than the normal operating voltage of the line and lower than the withstand voltage of the protected equipment. The M-LB-Ex-2615 on this site has a rated voltage […]
Are surge protective devices and lightning arresters the same thing?
Not exactly. Traditional ”lightning arresters” are mostly used for lightning protection in power systems; SPD is a broader term covering power, signal, […]
Does an SPD need grounding? How is it connected?
Yes. An SPD must discharge surge energy to earth, and grounding quality directly determines the protection effect. Signal SPDs are usually grounded via the shield layer or a dedicated grounding terminal […]
What is the "backup protection" of an SPD?
Backup protection refers to the fuse or circuit breaker upstream of the SPD, used to disconnect promptly when the SPD degrades or short-circuits, preventing fire or line faults. Many DIN-rail […]
What happens after an SPD fails? Is a status indicator required?
An SPD is a consumable device and will degrade and fail after multiple surge discharges. The failure mode is usually open circuit (loss of protection) or short circuit (possible fault), therefore a status […]
Can a standard SPD be used in an intrinsically safe circuit?
It cannot be used arbitrarily. Intrinsically safe circuits have strict energy limits, and any connected SPD must meet the intrinsic safety parameter requirements (capacitance, inductance, voltage limiting, etc.), otherwise it will compromise the intrinsic […]
What does the "clamping voltage" of a surge protective device mean?
Clamping voltage is the maximum value to which an SPD limits the line voltage when surge current passes through. It must be lower than the withstand voltage of the protected equipment while higher than the normal line […]
What does surge current 8/20 µs mean?
8/20 µs is a standard parameter simulating the lightning surge waveform: 8 µs front time and 20 µs time to half value. SPDs marked with R […]
Why do networks/fieldbuses require dedicated SPDs?
Buses such as Ethernet, Profibus and CAN are sensitive to line capacitance and impedance; the parasitic capacitance of a standard power SPD can cause signal distortion and communication […]
How is the P+F P-LB-1.C.123 surge protection isolator installed?
The P-LB-1.C.123 is a P+F single-channel surge protection isolator that plugs directly onto the field side of a KF module, used for analogue or digital signal trans […]
What is a surge protective device for Ethernet-APL?
Ethernet-APL is a high-speed Ethernet physical layer technology for process automation, and its spur ports require dedicated surge protection. The P+F M […] on this site
Why are surge protective devices important in process automation?
Long-distance signal and power cables in industrial sites act like "antennas" and easily pick up lightning overvoltages; switching of large motors and contactors […]
What are the main types of surge protective devices?
By protected object, they are divided into power SPDs and signal SPDs; signal SPDs are further subdivided into analogue/discrete, fieldbus, Ethernet and other types. By structure, […]
What are the features of the P+F M-LB-Ex-2615 surge protection isolator?
The M-LB-Ex-2615 is a P+F 3-channel surge protection isolator for ungrounded signal lines, rated voltage 1 V DC, maximum […]
What is a surge protective device (SPD)? What does it protect?
A surge protective device (SPD) is a protective device used to limit transient overvoltages and discharge surge currents […]
What is the difference between a surge protective device and a safety barrier?
The two have different roles. A safety barrier is explosion-protection associated apparatus that continuously limits the energy entering the hazardous area to prevent ignition of explosive gas; a surge protective device is a transient overvoltage protector […]


